PURPLE

PROFESSIONAL STRENGTH

INDUSTRIAL DEGREASER

DESCRIPTION

PURPLE is an extremely powerful and versatile cleaner and degreaser.  Its high performance formula is built to quickly dissolve stubborn grease and oil from engines, machinery, floors, trucks, and greasy equipment.  It is not recommended for use on aluminum. Care should be exercised when cleaning painted surfaces because it may damage paints if used too strong.  It is safe to use on iron, steel, stainless steel, galvanize, concrete, rubber, and plastic.

DIRECTIONS

Always test it on an inconspicuous area prior to use to test for adverse reaction.  PURPLE is easy and economical to use. Actual use concentration depends on the work to be done.

For light duty cleaning, dilute 1 part cleaner with 10 parts water.  Apply by spray or brush, allow to soak for a few minutes and scrub. Rinse with water.

For heavy duty cleaning, dilute 1 part cleaner with 5 parts water.  Apply by spray or brush, allow to soak for a few minutes. Scrub with a brush and rinse with water.

For degreasing, dilute 1 part cleaner with 50 parts water and apply with a hot water high pressure washer.  Rinse well with water.

Do not allow PURPLE to dry on any surface because streaking may occur.

CAUTION

CAUSES BURNS.  HARMFUL IF ABSORBED THROUGH SKIN.  Contains sodium hydroxide and 2-butoxyethanol.  Wear safety goggles and chemical resistant gloves and shoes when handling.  Eye contact may cause severe burns or blindness. Immediately flush eyes with water for at least fifteen minutes, holding eyelids open to insure complete flushing, and get medical aid.  Skin contact may cause severe irritation or burns, flush thoroughly with water. Swallowing may cause severe irritation or damage to the mucous membranes of the mouth, throat, and digestive tract.  If swallowed, DO NOT INDUCE VOMITING, immediately drink water to dilute and get medical aid. If inhaled, get fresh air, and get medical aid.

WARRANTY

Mobile Solvent & Supply, Inc. products are safe and effective when used as directed.  When using as a cleaner, always test a small area for adverse reaction. Since the manufacturer cannot control conditions or method of application, no warranty or liability beyond replacement of defective product is offered.

Parts Washer Solvent

PARTS WASHER SOLVENT

DESCRIPTION

This is a high quality, high flash point, low odor petroleum solvent.  Use it in soak tanks or recirculating solvent parts washers. It rapidly and safely removes even stubborn, baked on grease from all metals, and most rubber and plastics.  It won’t cause rust or corrosion.

It is recommended for use in Automotive Repair Shops, Car and Truck Dealers, Heavy Equipment Dealers, Marine Repair Yards, Oil Wells, Industrial Maintenance, Public Works Departments, Railroad Maintenance, Building Maintenance, and anywhere that grease and oil are a problem.

Oil reclaimers can use the spent solvent in fuel oil if it is not contaminated with carburetor cleaners, flammable solvents, etc.  

DIRECTIONS

It is ready to use in soak tanks and re-circulating solvent parts washers.  Apply by spray, brush, rag, or dipping. Allow to soak, or scrub with a brush.  Wipe dry with a towel or let it air dry.

CAUTION

Wear protective gloves and eye protection when using solvents.

Eye contact causes irritation.  Immediately remove contact lenses and flush eyes with plenty of water, lifting eyelids to insure thorough flushing.

Skin contact may cause irritation.  Repeated or prolonged skin contact may de-fat the skin.  Wash with soap and water.

Inhalation of excessive amounts of vapors or spray mists may cause respiratory irritation.  Remove to fresh air.

Ingestion may be harmful.  Aspiration hazard if swallowed.

WARRANTY

Mobile Solvent & Supply, Inc. products are safe and effective when used as directed.  When using as a cleaner, always test a small area for adverse reaction. Since the manufacturer cannot control conditions or method of application, no warranty or liability beyond the replacement of defective product is offered.

KEEP OUT OF REACH OF CHILDREN

Opticlean

LAUNDRY DETERGENT


Super-concentrated heavy-duty detergent for use in hard or soft water

Effectively removes greases, soils, stains

Especially well suited for white shirts and linens

Its optical brightener system makes whites whiter and colors brighter

Biodegradable: phosphate free

Color safe bleaching protects fabric colors

Removes bad odors

Low foam

Recommended for commercial laundries

Prevents re-deposition of soils

Sequesters metal ions, prevents scale build-up in washing machines

DIRECTIONS

Opticlean is very economical and requires low dosing quantities.  The following recommendations are based on normal soils and a 50 lb wash load.

Shirts: 4 oz

Linens: 6 oz

Uniforms: 8 oz

Use caution when washing fabrics of low colorfastness to prevent color changes.

CAUTION

Eye contact will cause irritation.  Repeated or prolonged skin contact may cause dryness or chapping.  Inhalation of dusts may be harmful. May be harmful if swallowed. In case of eye contact, flush with plenty of water for fifteen minutes.  Get medical aid if irritation persists. In case of skin contact, wash with water. If inhaled, get fresh air. If swallowed, do not induce vomiting, drink water and get medical aid.

WARRANTY

Mobile Solvent & Supply, Inc. products are safe and effective when used as directed.  When using as a cleaner, always test a small area for adverse reaction. Since the manufacturer cannot control conditions or method of application, no warranty or liability beyond the replacement of defective product is offered.

Opti-Maxx

LAUNDRY DETERGENT


Super-concentrated heavy-duty detergent for use in hard or soft water

Effectively removes greases, soils, stains

Especially well suited for white shirts and linens

Its optical brightener system makes whites whiter and colors brighter

Biodegradable: phosphate free

Color safe bleaching protects fabric colors

Removes bad odors

Low foam

Recommended for commercial laundries

Prevents re-deposition of soils

Sequesters metal ions, prevents scale build-up in washing machines

DIRECTIONS

Opti-Maxx is very economical and requires low dosing quantities.  The following recommendations are based on normal soils and a 50 lb wash load.

Shirts: 4 oz

Linens: 6 oz

Uniforms: 8 oz

Use caution when washing fabrics of low colorfastness to prevent color changes.

CAUTION

Eye contact will cause irritation.  Repeated or prolonged skin contact may cause dryness or chapping.  Inhalation of dusts may be harmful. May be harmful if swallowed. In case of eye contact, flush with plenty of water for fifteen minutes.  Get medical aid if irritation persists. In case of skin contact, wash with water. If inhaled, get fresh air. If swallowed, do not induce vomiting, drink water and get medical aid.

WARRANTY

Mobile Solvent & Supply, Inc. products are safe and effective when used as directed.  When using as a cleaner, always test a small area for adverse reaction. Since the manufacturer cannot control conditions or method of application, no warranty or liability beyond the replacement of defective product is offered.

MAXX-BRIGHT

SUPER CONCENTRATED

ALUMINUM BRIGHTENER AND CLEANER

DESCRIPTION

This highly concentrated, heavy duty cleaning and brightening agent removes unsightly oxidation, diesel smoke, oil, and dirt from aluminum surfaces.  It removes the most stubborn soils and produces a fresh, new aluminum surface. It contains acids, penetrants, detergents, and emulsifiers in combination designed to provide efficiency and economy in cleaning aluminum.

DIRECTIONS

MAXX-BRIGHT should be diluted with water.  Solution concentration will depend upon the job and equipment available, although the usual ratio is 1 part cleaner to 15 parts water.  It may be applied by spray or brush. The surface to be cleaned should first be wet with water and MAXX-BRIGHT applied from the bottom up to prevent streaking.  Agitate the surface with a brush if necessary and allow the cleaner to remain on the surface for approximately ten minutes; do not allow to dry. If allowed to dry on the vehicle, streaking may occur.  Flush thoroughly with water to remove cleaner and stop it’s action.

CAUTION

Contains sulfuric acid and ammonium bilfuoride, corrosive and poison.  May cause burns to eyes and skin. May be harmful if swallowed. In case of eye contact, flush with plenty of water for at least 15 minutes, and get medical aid.  In case of skin contact, flush with water and get medical aid if needed. If swallowed, DO NOT INDUCE VOMITING, drink large amounts of water and get medical aid immediately.

WARRANTY

Mobile Solvent & Supply, Inc. products are safe and effective when used as directed.  When using as a cleaner, always test a small area for adverse reaction. Since the manufacturer cannot control conditions or method of application, no warranty or liability beyond replacement of defective product is offered.

KEEP OUT OF REACH OF CHILDREN

Maxx-Bright

MAXX-BRIGHT

SUPER CONCENTRATED

ALUMINUM BRIGHTENER AND CLEANER

DESCRIPTION

This highly concentrated, heavy duty cleaning and brightening agent removes unsightly oxidation, diesel smoke, oil, and dirt from aluminum surfaces.  It removes the most stubborn soils and produces a fresh, new aluminum surface. It contains acids, penetrants, detergents, and emulsifiers in combination designed to provide efficiency and economy in cleaning aluminum.

DIRECTIONS

MAXX-BRIGHT should be diluted with water.  Solution concentration will depend upon the job and equipment available, although the usual ratio is 1 part cleaner to 15 parts water.  It may be applied by spray or brush. The surface to be cleaned should first be wet with water and MAXX-BRIGHT applied from the bottom up to prevent streaking.  Agitate the surface with a brush if necessary and allow the cleaner to remain on the surface for approximately ten minutes; do not allow to dry. If allowed to dry on the vehicle, streaking may occur.  Flush thoroughly with water to remove cleaner and stop it’s action.

CAUTION

Contains sulfuric acid and ammonium bilfuoride, corrosive and poison.  May cause burns to eyes and skin. May be harmful if swallowed. In case of eye contact, flush with plenty of water for at least 15 minutes, and get medical aid.  In case of skin contact, flush with water and get medical aid if needed. If swallowed, DO NOT INDUCE VOMITING, drink large amounts of water and get medical aid immediately.

WARRANTY

Mobile Solvent & Supply, Inc. products are safe and effective when used as directed.  When using as a cleaner, always test a small area for adverse reaction. Since the manufacturer cannot control conditions or method of application, no warranty or liability beyond replacement of defective product is offered.

KEEP OUT OF REACH OF CHILDREN

Magnum

MAGNUM

CONCENTRATE

BLEACH COMPATIBLE

DESCRIPTION

MAGNUM is concentrated for full strength cleaning.  It is stable when used with bleach to remove mildew, mold,  algae, and brighten wood decks, fences, and furniture. It is an excellent all purpose cleaner and degreaser.  Use it full strength for heavy duty cleaning or dilute with water for lighter jobs. It emulsifies and removes grease, oils, and soils from surfaces being cleaned.  It suspends dirt and foreign material and allows it to be wiped or flushed away. Safe to use on most finishes and is recommended for cleaning engines and underhood painted surfaces, aluminum, whitewall tires, walls floors, vinyl upholstery, lawn furniture, outdoor grills, ceramic tile, porcelain fixtures, fiberglass boats, and glass.  It is excellent for use in steam cleaning machines and high pressure washers. It will remove oil, grease, dirt, road film, heel marks, finger prints, and kitchen grease.

DIRECTIONS

MAGNUM is concentrated and should diluted for optimum economy.

Dilute it up to 1 part per gallon of bleach to remove mildew and brighten woodwork.  

For all purpose cleaning, dilute 1 part cleaner with 50 to 75 parts water.

Whitewall tires, dilute 1 part cleaner with 5 parts water.

Heavy soils such as floors, outdoor grills, fiberglass boats, machinery, engines, and greasy tools, dilute 1 part cleaner with 10 parts water.

For steam cleaning and high pressure washing, dilute 1 part cleaner with 75 to 100 parts water.

CAUTION

Avoid contact with eyes and skin.  Do not take internally. In case of eye contact, immediately flush with water for at least fifteen minutes and consult physician if irritation persists.  If swallowed, DO NOT INDUCE VOMITING, drink large amounts of water and consult physician. In case of skin contact, flush with plenty of water.

WARRANTY

Mobile Solvent & Supply, Inc. products are safe and effective when used as directed.  When using as a cleaner, always test a small area for adverse reaction. Since the manufacturer cannot control conditions or method of application, no warranty or liability beyond the replacement of defective product is offered.

KEEP OUT OF REACH OF CHILDREN

Luma Bright

LUMA BRIGHT

CONCENTRATE

DESCRIPTION

This is a heavy duty cleaning and brightening agent which removes oxidation, diesel smoke, oil, and dirt from aluminum surfaces, producing a lustrous satin appearance.  It contains acids, penetrants, and emulsifiers in combination designed to provide efficiency and economy in cleaning aluminum.

INSTRUCTIONS

LUMA BRIGHT should be diluted with water.  Solution concentration will depend upon the job and equipment available, although the usual ratio is 1 part cleaner to 9 parts water.  It may be applied by brush, or spray. The surface to be cleaned should first be wet with water and LUMA BRIGHT applied from the bottom up to prevent streaking.  Scrub the surface with a brush if necessary and allow the cleaner to remain on the surface for a short time, but do not allow it to dry. If allowed to dry on the vehicle, streaking may occur.  Flush thoroughly with water to remove cleaner and stop it’s action.

CAUTION

Corrosive-contains Phosphoric Acid.  May cause burns to eyes and skin. May be harmful if swallowed.  In case of eye contact, flush with plenty of water for at least fifteen minutes, and get medical aid.  In case of skin contact, flush with water and get medical aid if needed. If swallowed, DO NOT INDUCE VOMITING, drink large amounts of water and get medical aid immediately.

NOTICE

Mobile solvent & Supply, Inc. products are safe and effective when used as directed.  When using as a cleaner, always test a small area for adverse reaction. Since the manufacturer cannot control conditions or method of application, no warranty or liability beyond the replacement of defective product is offered.

KEEP OUT OF REACH OF CHILDREN

Leak Detector Solution

LEAK DETECTOR

SOLUTION

DESCRIPTION

Leak Detector Solution is a salt-free, non-alkaline, biodegradable, water base combination of foaming agents designed to detect leaks in tanks, refrigeration systems, and other pressurized vessels.

INSTRUCTIONS

Use it full strength or dilute with water as desired. Apply by brush, spray, or squeeze bottle. Rinsing is not necessary in most cases, however, if the item is to be painted, the user should test effect of Leak Detector on paint adhesion.

CAUTION

May cause eye irritation. In case of eye contact, flush with water.

NOTICE

Mobile Solvent & Supply, Inc. products are safe and effective when used as directed. When using as a cleaner, always test a small area for adverse reaction. Since the manufacturer cannot control conditions or method of application, no warranty or liability beyond the replacement of defective product is offered.

KEEP OUT OF REACH OF CHILDREN

Hot Tank Compound

HOT TANK COMPOUND

DEGREASER, DERUSTER,

AND PAINT REMOVER

DESCRIPTION

HOT TANK COMPOUND is a heavy duty liquid alkaline product used to clean ferrous metals by the hot vat soaking method.  It removes rust, grease, oils, engine varnish, grime, heat-hardened resins, tar, and other stubborn soils. It cleans automobile radiators quickly and thoroughly.  Mechanical agitation may be used if desired. Agitation reduces immersion time by producing a scrubbing effect on the parts being cleaned.

DIRECTIONS

HOT TANK COMPOUND should be used at 10 – 15 percent concentration and heated to 200° F. or higher.  Immersion times may vary from a few minutes to about two hours depending on concentration, temperature, and agitation.  A pressure rinse with water is used to flush away the loosened soils.

When charging the tank, fill half full with cold water.  Add HOT TANK COMPOUND slowly with mixing. Heat will be generated when the compound is added to the water.  Add remainder of water and heat the tank.

CAUTION

Corrosive, contains sodium hydroxide, UN 1824.  Corrosive to animal tissues. Eye contact may cause severe burns or blindness.  In case of eye contact, immediately flush with water for at least 15 minutes and get medical aid.  Skin contact may cause severe irritation or chemical burns.  In case of skin contact, flush with water. Ingestion may cause severe irritation or damage to the mucous membranes of the mouth, throat, and digestive tract.  If swallowed, DO NOT INDUCE VOMITING, immediately drink large amounts of water and get medical aid.

NOTICE

Mobile Solvent & Supply, Inc. products are safe and effective when used as directed.  When using as a cleaner, always test a small area for adverse reaction. Since the manufacturer cannot control conditions or method of application, no warranty or liability beyond replacement of defective product is offered.

KEEP OUT OF REACH OF CHILDREN